What Bitrate Converter helps you do

Convert between bps, kbps, Mbps and Gbps, and see the matching byte-per-second rates, all using decimal SI units. One workspace for normalizing bitrate figures from audio, video, network and storage sources. It accepts a value in any supported unit and updates the other columns together, so you do not have to chain single conversions.

All conversions run in your browser. No rate data is uploaded to Haivix.

How it works

These converters apply a fixed factor or formula to the value you enter, inside the page. They do not fetch live rates, measurement standards or device data, so the result depends only on the number and the units you choose. Values are formatted to a handful of decimals, with scientific notation for very small or very large results. Where a formula needs a second input, such as voltage, hours or a power factor, the page asks for it rather than assuming a value. The factor itself comes from the unit definition, so it is the same today as it will be next year; only the input changes.

How to use Bitrate Converter

Enter a bitrate and choose its unit.
Read the equivalent across the other bit units and the byte-per-second equivalents.
Pick the column that matches the target system.
Copy whichever figure you need.

When to use it

Normalize bitrate values collected from different tools into one unit.
Check a video stream bitrate against an available link capacity.
Convert bits to bytes when comparing a network rate with a file size.
Translate a router's bps figure into the MB/s a download manager shows.
Compare an audio bitrate with a video bitrate on the same scale.
Explain to someone why a 100 Mbps line does not download at 100 MB/s.

When not to use it

Do not use it for binary units such as kibibytes or mebibits.
Do not expect it to account for protocol overhead or encoding efficiency.
Do not treat a nominal link rate as a guaranteed download speed.

Example

1 Mbps is 1000 kbps and 125 KB per second, because there are 8 bits in a byte. 100 Mbps is 12.5 MB/s. 1 Gbps is 1000 Mbps, or 125 MB/s. The byte columns are always one eighth of the matching bit column.

What you can do with Bitrate Converter

Convert across bps, kbps, Mbps and Gbps.
Show the matching B/s, KB/s, MB/s and GB/s rates.
Update every column from a single input.
Handle fractional and large values.
Use decimal SI prefixes throughout.
Run the conversion locally with no upload.

Example: check the unit before trusting the number

Confirm the source unit and the target unit before reading the result. A correct number in the wrong unit is the most common conversion mistake, especially between US and imperial measures.

Sanity-check the magnitude with a rough mental estimate. If kilometres should be larger than miles and the result is smaller, the direction is reversed.

Round the result for the destination. A calculator can show six decimals, but an invoice, label or form usually needs two or three, and the rounding rule may be specified.

Keep the original value and unit in your notes. If the destination rejects the result, the source is the only way to recompute without guessing what was entered.

Check whether the unit has regional variants. Gallons, pints, tons and acres all have more than one definition, and picking the wrong one can shift the result by several percent without any arithmetic error.

If the answer will drive a purchase, a dose or a safety decision, verify it against a second source or the manufacturer's own table. A calculator removes arithmetic mistakes, not definition mistakes.

What to know before you start

Uses decimal SI units rather than binary multiples.
Byte rates assume eight bits per byte and ignore encoding overhead.
It does not model packet headers, retransmissions or contention.
The displayed values are rounded to a limited number of decimals.

Common mistakes

Forgetting to divide by eight when comparing bits with bytes.
Mixing decimal prefixes with binary ones such as KiB.
Assuming a 100 Mbps plan downloads at 100 MB/s.
Reading the wrong column after changing the input unit.

Troubleshooting

If the byte figure looks eight times too small, the bit-to-byte factor was forgotten.

If the number does not change, confirm the input unit matches the value entered.

If the result is unexpectedly large, a unit may have been changed without re-entering the value.

If a binary unit is required, this converter will not match it exactly.

Bitrate Converter