What Bytes Converter helps you do

Convert a data size between bytes, kilobytes, megabytes, gigabytes and terabytes so you can read storage quotes, file limits and log sizes in the unit you think in. Each unit is shown for the same input. This page uses 1024-based multiples, so one kilobyte is 1024 bytes rather than 1000.

Conversions are done entirely in your browser. The values you type are never uploaded to Haivix.

How it works

These converters apply a fixed factor or formula to the value you enter, inside the page. They do not fetch live rates, measurement standards or device data, so the result depends only on the number and the units you choose. Values are formatted to a handful of decimals, with scientific notation for very small or very large results. Where a formula needs a second input, such as voltage, hours or a power factor, the page asks for it rather than assuming a value. The factor itself comes from the unit definition, so it is the same today as it will be next year; only the input changes.

How to use Bytes Converter

Enter the size into the unit you already have, such as megabytes.
Read the equivalent in every other unit in the results list.
Check the byte count if you need the exact figure.
Copy the figure you need for a form, ticket or spec sheet.

When to use it

Translate a 25 MB upload limit into kilobytes before checking a file size.
Compare a hosting plan quoted in GB with a log file measured in MB.
Convert a storage figure from a cloud bill into bytes for a capacity script.
Read a disk size the way an operating system reports it.
Check whether a file fits a limit expressed in another unit.
Normalize several file sizes before adding them up.

When not to use it

Do not use it for network bit rates; bytes and bits differ by eight.
Do not expect decimal SI sizes as used by drive manufacturers.
Do not use it for memory bandwidth or throughput.

Example

1 KB is 1024 bytes. 1 MB is 1024 KB, or 1,048,576 bytes. 1 GB is 1024 MB. A 4 MB photo is 4096 KB, or 4,194,304 bytes. A 1 TB drive is 1024 GB in these units, though the marketed capacity uses decimal prefixes.

What you can do with Bytes Converter

Convert between B, KB, MB, GB and TB.
Show every unit for a single input.
Use 1024-based multiples throughout.
Handle fractional values.
Show four decimal places for each unit.
Run the conversion locally with no upload.

Example: check the unit before trusting the number

Confirm the source unit and the target unit before reading the result. A correct number in the wrong unit is the most common conversion mistake, especially between US and imperial measures.

Sanity-check the magnitude with a rough mental estimate. If kilometres should be larger than miles and the result is smaller, the direction is reversed.

Round the result for the destination. A calculator can show six decimals, but an invoice, label or form usually needs two or three, and the rounding rule may be specified.

Keep the original value and unit in your notes. If the destination rejects the result, the source is the only way to recompute without guessing what was entered.

Check whether the unit has regional variants. Gallons, pints, tons and acres all have more than one definition, and picking the wrong one can shift the result by several percent without any arithmetic error.

If the answer will drive a purchase, a dose or a safety decision, verify it against a second source or the manufacturer's own table. A calculator removes arithmetic mistakes, not definition mistakes.

What to know before you start

The tool uses 1024-based multiples, so 1 KB is 1024 bytes rather than 1000.
It labels those multiples KB, MB and GB rather than KiB, MiB and GiB.
Operating systems and drive vendors disagree on which convention to display.
Values are shown to four decimal places, so very large figures are rounded.

Common mistakes

Assuming 1000 bytes in a kilobyte; this page uses 1024.
Comparing a Windows file size with a drive manufacturer's decimal GB.
Confusing bytes with bits when reading a network speed.
Forgetting that each step multiplies by 1024, not 1000.

Troubleshooting

If the number is smaller than a drive label suggests, the label uses decimal units.

If the result looks 1024 times off, the input unit was chosen incorrectly.

If the byte count is fractional, the input had a fraction; bytes are usually whole.

If a limit check fails, confirm whether the service counts decimal or binary units.

Bytes Converter